Home |  Mail |  Sitemap |  Imprint
 
 Deutsch
  • Quick search for DIN
| CONTACT |
Magnetfabrik Bonn GmbH

Tel.: +49(0)228 72905-0
Fax: +49(0)228 72905-37
| Rare earth polymer bound magnets |
 minimum value
DescriptionDIN IEC
60404-8-1
codes 1		i/aBH(max)
[kJ/m3] 6		Br
[mT] 6		HcB
[kA/m] 6		HcJ
[kA/m] 6		Density
[g/cm3]		Water
absorption
[%] 7		CompositionProduction
Neofer 25/60pREFeB 27/60pi274002606304,350,05NdFeB + PA11Injection modeling 4
Neofer 31/100pREFeB 30/100pi3040029010004,500,05NdFeB + PA11Injection modeling 4
Neofer 41/100pREFeB 36/100pi3646031010004,850,05NdFeB + PA11Injection modeling 4
Neofer 37/60pREFeB 37/60pi374703006004,600,05NdFeB + PA11Injection modeling 4
Neofer 39/60pREFeB 39/60pi394853106004,800,05NdFeB + PA11Injection modeling 4
Neofer 44/60pREFeB 44/60pi445203206005,000,05NdFeB + PA11Injection modeling 4
Neofer 48/60pREFeB 48/60pi485403306005,100,05NdFeB + PA11Injection modeling 4
Neofer 55/50pREFeB 52/52pi525803305204,850,05NdFeB + PA11Injection modeling 4
Neofer 65/70pREFeB 64/60pi646304006005,750,05NdFeB + PA12Injection modeling 4
Neofer 55/100pREFeB 55/100pi5558040010005,90n.a.NdFeB + EPHPressing 4
Neofer 62/60pREFeB 62/60pi626503806005,90n.a.NdFeB + EPHPressing 4
The Neofer® p magnets use an isotropic NdFeB-based rare-earth material which is compounded with thermoplastic binders. The Neofer® p material types are magnetized after molding, since they are isotropic and thus not directional.

The advantage of the injection molding process for producing magnets lies in the wide range of shapes that can be produced. It is also possible for inserts such as axles, bushes or rings to be molded in, with the inserts being loaded by hand or fully automatically, depending on the quantity produced. The costs of assembly operations can be reduced as such materials allow press-fit, snap-fit and positive-fit connections with motor shafts etc.

The production process allows products to be manufactured within such tight tolerances that no reworking is generally necessary. Depending on the size of the molding, the tolerances that can be achieved are in the range 0.03 through 0.25 mm. As required, polymer-bonded materials can be turned, drilled, milled and ground and they are not as brittle as sintered materials.

The proportion of synthetic plastic materials of typically ten percent by weight mean that the magnetic properties lie below those of unmixed material. On the other hand, with anisotropic grades, it is possible to achieve a directional magnetization during the injection molding process. This in turn improves the magnetic properties.

NdFeB magnets are particularly suitable when strong magnetic fields are required in small volumes, e.g. in sensor technology..


  1. Gebildet aus angenäherten Mindestwerten von (B * H)max und HcJ nach DIN IEC 60404-8-1.
    Combined of approximated minimum values of (B * H)max and HcJ according to DIN IEC 60404-8-1.
    Composé de valeurs minimales (B * H)max et HcJ suivant DIN IEC 60404-8-1.

  2. PA = Polyamid/ Nylon
    NBR = Nitrylbutylenrubber
    EPH = Expoxydharz/Resin
    PPS = Polyphenylensulfid

  3. Vorzugsrichtung zur Kalandrierrichtung.
    Prefered axis to rolling direction.
    Sens préférentielle d’ aimantation au sens de calandrage.

  4. Spanabhebend bearbeitbar.
    Machinable by cutting.
    Usinable par enlèvement de copeaux.

  5. Die maximale Einsatztemperatur ist abhängig von der Anwendung, von der Magnettype sowie der Magnetgeometrie. Für weitere Informationen kontaktieren Sie bitte unsere Anwendungstechniker.
    The maximum operating temperature for a magnet matrials is dependent upon the specific application and magnet geometry. Do not hasitat to contact our Application Engineers for more information.
    La température maximale d'utilisation d'un aimant dépend de son application spécifique ainsi que de sa géométrie. N'hésitez pas à prendre contact avec nos ingénieurs d'application pour plus d'informations.

  6. Angegebene Werte nur bei optimalen Abmessungen: Kürzeste Kante > 8 mm, Volumen 1 – 200 cm³.
    Indicated values only with optimum dimensions: shortest edge > 8 mm, volume 1 – 200 cm³.
    Valeurs uniquement pour dimensiones optimales côté le plus court > 8 mm, volumes 1 – 200 cm³.

  7. t.b.d.
    to be defined
    noch festzulegen
    à établir
    n.a.
    not applicable
    nicht angegeben / anwendbar
    pas applicable
    8.
Magnetfabrik Bonn © 2008